Difference between revisions of "Electronics"

From Hive13 Wiki
Jump to navigation Jump to search
(Testing tools we have)
(Programmers, Power supplies, etc.)
Line 48: Line 48:
 
* Several other oscopes that are untested/not set up - scattered
 
* Several other oscopes that are untested/not set up - scattered
  
=== Programmers, Power supplies, etc. ===
+
=== Programmers, Development Boards, etc. (Located in plastic drawers under bench) ===
  
 +
*TI Stellaris Launchpad LM4F120 (arduino compatible dev board)
 +
*TI C2000 Piccolo Launchpad xL-F28027 (arduino compatible dev board)
 +
*2 TI MSP430 Launchpads (arduino compatible dev board)
 
*Olimex USB JTAG with OpenOCD debugger support ( [http://www.olimex.com/dev/arm-usb-tiny.html link] ) (hive13)
 
*Olimex USB JTAG with OpenOCD debugger support ( [http://www.olimex.com/dev/arm-usb-tiny.html link] ) (hive13)
*usbtinyisp AVR microcontroller programmer  ( [http://www.ladyada.net/make/usbtinyisp/ link]) (cjdavis  Uses AVRDUDE programmer software.  ([http://www.ladyada.net/learn/avr/avrdude.html instructions])
+
*Adafruit usbtinyisp AVR microcontroller programmer  ( [http://www.ladyada.net/make/usbtinyisp/ link]) (cjdavis  Uses AVRDUDE programmer software.  ([http://www.ladyada.net/learn/avr/avrdude.html instructions])
 +
*OneFrog USB-Serial bridge
 +
*Datarase EPROM eraser
 
*Willem Parallel port EPROM programmer ([http://www.mcumall.com/Forum/forum.asp?FORUM_ID=3 link]) (hive13)
 
*Willem Parallel port EPROM programmer ([http://www.mcumall.com/Forum/forum.asp?FORUM_ID=3 link]) (hive13)
 +
*HackRFBlue Software Defined Radio
 
*Serial interface Smart Card programmer for Satellite use (unknown, need to track down docs) (hive13)
 
*Serial interface Smart Card programmer for Satellite use (unknown, need to track down docs) (hive13)
*Sparkfun USB->TTL converter with FT232 chip
+
*Crystal Fontz LCD
*"Hondalog" FTDI USB->TTL interface with FT232 chip([http://www.moates.net/xtreme-hulog-honda-usb-datalog-interface-p-78.html product] [http://wikitest.pgmfi.org/twiki/bin/view.pl/Library/WebHome?topic=OBD1CN2 pin-config]) (hive13) - in box close to wall under workbench
+
*Amex CC card reader
*Pasco model 8000 adjustable power supply - located on main workbench area close to scope
+
*Lattice XP2 Brevia DevKit dev board and programmer
Note: many of these are AWOL as of 3-13. You may have to look hard.
 
  
 
=== Dev boards ===
 
=== Dev boards ===

Revision as of 17:27, 17 July 2015

The Electronics Area

The electronics area exists on the two desk areas in the portion of the two pallet racks that are closest to the window. (Located in 3C) It is divided roughly into an assembly area (closest to the meeting area) and a testing area (closest to the dirty room). There is an anti-static mat down on top of both desks.

We're starting to get a useful collection of things for working with electronics. I decided to try to document what all we have because I heard at least three people say, "Wow, we have one of those?"

Items on loan to the hive are parenthetically noted. Items owned by the hive are noted 'hive13'

So without further ado...

BTW, please feel free to add more information / details!

Soldering Tools in the Area

  • Weller WES50 Temperature control soldering iron (cjdavis) - located on top of workbench, plugged in
  • Xytronic 968 Combination temperature control soldering iron / vacuum desoldering iron station (daveb) - located on top of workbench, plugged in
  • Soldering tweezers (player2) ( link)
  • Weller activated carbon fume extractor fan (LorinP) - located on solder bench, plugged in
  • Leaded Rosin core solder, several rolls (hive13) - located on shelf of soldering bench
  • Lead free solder, one or two rolls (hive13) - located on shelf of soldering bench
  • Three tool trays containing tweezers, hemostats, wire strippers, and other hand tools. IMPORTANT: When using these tools away from the primary electronics bench, please take the entire tray so electronics tools stay together and get returned. "Grab a tray, not a tool!".
  • 2x4 stand that says "SMT ONLY" with solder tip cleaner, 28AWG No-clean solder for SMT work, 28 AWG water clean up solder for SMT work, and 21 AWG water clean up solder for SMT work. Please note: this solder is expensive (~$50 / lb - roll) so do not use it for through-hole stuff. (hive13) - located on top of workbench by soldering irons.
  • Flux pens, liquid flux, solder paste. In mini fridge below bench. Make sure this fridge stays on, these items must be stored cold.
  • Solder Paste dispenser - this is not actively set up but it is a matter of connecting attachments and going to town. (hive13) - located in labeled box on shelf above soldering bench.
  • Shop air compressor quick connect.
  • Reflow oven - stainless steel toaster oven with homebrew PID temperature controller (hive13)
  • Stereo Microscope (jon) - assembly area, comes and goes
  • Wire, clips, leads, etc - hanging on wall.
  • Large Panavise circuit board holder (LorinP)
  • Nifty flexible 3rd hand (Jon)
  • Traditional 3rd hand
  • Magnifier lamps, headbands, lenses.
  • Wave solder machine (daveb) - dirty room for storage, by a dedicated 20A circuit plug to use

Testing tools we have

  • Tektronics 453 analog scope (hive13) link more info
  • Tenma 40 Mhz oscilloscope (hive13) - located on bench
  • Rigol 50Mhz DSO (daveb) - located on testing bench
  • Regulated, adjustable power supplies (hive13)
  • Wavetech function generator
  • Isolation tranformer
  • BitScope USB logic analyzer - located on testing bench
  • HP 3437A 7.5 digit bench multimeter link manual
  • Handful of cheap multimeters - located on wire shelf
  • Test leads, BNC's, and probes - hung in lead holder mounted on window sill
  • Alligator clip leads, meat hooks (grabber clips), jumber wires - hung in lead holder
  • Extech lead adapter kit to use clip, probe, meat hook on any test equipment. - in plastic drawers below bench.
  • Several other oscopes that are untested/not set up - scattered

Programmers, Development Boards, etc. (Located in plastic drawers under bench)

  • TI Stellaris Launchpad LM4F120 (arduino compatible dev board)
  • TI C2000 Piccolo Launchpad xL-F28027 (arduino compatible dev board)
  • 2 TI MSP430 Launchpads (arduino compatible dev board)
  • Olimex USB JTAG with OpenOCD debugger support ( link ) (hive13)
  • Adafruit usbtinyisp AVR microcontroller programmer ( link) (cjdavis Uses AVRDUDE programmer software. (instructions)
  • OneFrog USB-Serial bridge
  • Datarase EPROM eraser
  • Willem Parallel port EPROM programmer (link) (hive13)
  • HackRFBlue Software Defined Radio
  • Serial interface Smart Card programmer for Satellite use (unknown, need to track down docs) (hive13)
  • Crystal Fontz LCD
  • Amex CC card reader
  • Lattice XP2 Brevia DevKit dev board and programmer

Dev boards

  • Lattice XP2 Brevia FPGA dev kit - complete and in box (link) (hive13)
  • Stellaris LM3S811 Cortex 50 Mhz Cortex M3 ARM - complete and in box (link) (hive13)
  • mbed NXP1768 96 Mhz Cortex M3 ARM - complete and in box (docs) (blundar)
  • Olimex 70 Mhz ARM7TDMI ARM NXP LPC2103 dev board - needs Olimex USB JTAG (link) (hive13)
  • Renesas M16C dev board with RTA-FoUSB-MON debugger/programmer (no link)
  • Ti MSP430 LaunchPad (MSP-EXP430G2) and Capacitive Touch BoosterPack (430BOOST-SENSE1) x2 (link) (cjdavis)
  • STM32L-DISCOVERY (STM32F152 - 32Mhz low power Cortex-M3 ARM) can also be used as a USB ST-Link debug interface. Product page (hive13) (used for Reflow oven)
  • STM32F4-DISCOVERY (STM32F407 - 168Mhz 1Mbyte flash / 192k RAM / floating point Cortex-M4) Has accelerometer and a bunch of other goodies, USB interface. Product page (hive13) (missing?)

Projects

  • Toaster Oven reflow oven for solder paste / surface mount soldering. Mostly functional as of Mar-2013. Would be nice to have a display. Would be nice to program temp curves.
  • CNC Solder paste dispenser/applicator - planning stage.
  • Refine SMT assembly methods

Wish list

  • Convert some computer power supplies into +5 / +12v power supplies. Mount under bench to avoid clutter.
  • Another decent soldering iron or two.

Electronic components

  • There is a fairly large selection of wire on racks by the window ranging from about 10 AWG to 24 AWG.
  • add me!!!


Consumable Supplies

The main consumable supplies in the electronics area are solder and soldering supplies. For many of these things, other brands/part numbers may work ok. These part numbers are for the exact replacement of what has been used successfully at the Hive:

  • The Flux pen for hand SMT soldering Kester 2331-zx (may be discontinued)
  • 21 AWG Water clean solder - Kester 24-6337-6403 $65/lb-roll (Digikey: KE1300-ND)
  • 28 AWG Water clean solder - Kester 24-6337-6422 $90/lb-roll (Digikey: KE1303-ND)
  • 28 AWG No-Clean solder - Kester 4-6337-8806 $91/lb-roll (Digikey: KE1405-ND)

Borked Items

Stuff breaks. We have a decent amount of broken or marginally working stuff. Eventually this stuff might get fixed or repaired but for now it's just broken.

  • Tenma 72-6340 De-soldering iron (player2) - located in "broken solder stuff box" above assembly area
  • Tenma 72-925 Temperature control soldering iron (hive13) - located on top of workbench, plugged in