|Start Date: 4/01/2014|
Apiary - an area ("ary"-a?) of apes ("AH-pays" : Latin for "bees") and their hives.
This project is intended to allow members (apes: pronounce it as you will) at school or Mini Maker Faires to carry & show off a portable sample of the wide variety of skills/machine-areas (hives) available to members at Hive 13.
The code on the Arduino now has a GitHub repo.
2 September 2015: Code Rewrite!
The first 2.x version of the code is now up. Animation works much smoother, and is written time-independently. Currently set to 10 ms per animation tick. Additionally, the chaser lights now start white, then as it speeds up they become more colorful.
Currently uses about 21% of program memory and %5 of dynamic memory for globals.
28 August 2015: Show Prep: Gluing Things Down
The brackets have been affixed to the bottom panel so things don't fly to pieces at the slightest provocation. Additionally, the code is finally up on GitHub, along with a rewrite started on the branch 2015-rewrite.
13 January 2015
Red & black brackets for the Apiary Arduino, breadboard and 2 servos. 3D printed, designed by Joseph S.
12 September 2014: The Apiary lives!
Apiary 0.5: Laser cut logo; 3D printed logo; cut & brazed metal frame; hive-made wooden & Lexan® carcase; home-made wood stain;
servos; Arduino; LED strip; CdS sensor; 5vdc 1A wall wart; 2 clamps to hold it together for now! Software from Arduino.cc & AdaFruit with some special modifications by Joseph Sikorski.
(White backround is for photo, normally the frame backround is open.)
Logo goes about 45º L & R of flat, LEDs march along strip; these actions speed up when the CdS is covered.
First photo: 24 March 2014
Replaced wood floor with Masonite® floor
Clearance above shield with separate, removable Masonite® mounting board in place atop floor
Case assembled and stained.
5 August 2014: Update to frame: Welds at corners changed
23 July 2014
Update to frame: 3/4" "L" beam; rails 13 3/4" (with 4 holes); stiles 8", frame outside dim.s: 14"x8".
Rails to be welded to back of stiles, flush w/ top & bottom (bottom rail orientation corrected)
5 Aug 14: Rods placed; nuts shown
11 Aug 14
Proposed electronics shown (sensor; logo mover; display; tethered robot); fiber and 3D printing on logo
21 Aug 14
Note above High Speed Stop Action Photos of Apiary in Action!! "It's working! It's working!"
Note: logo is presented via High Tech 2D Printing - 3D to Follow!!
Dave helped get the frame cut and brazed; Ryan helped get the servo proof of concept running;
Clean & apply finish to frame
3d Print the H, CNC the I/1 & E/3(wood?) and laser cut/engrave the V (lexan®?). Fiber on the I or both the I & 1
sensors (and programming) to activate the box as visitors approach;
tiny tethered robot - would like a tiny bot that follows a line (visitors could draw and watch it follow)-would like it as small as possible with a Hive 13 3D printed bee shell
set up for a laptop battery with AC backup
Get the electronics spec'd & bought.
Get the assembled &electronics installed.
23 Jul 14
Alternate stiles; holes shown
7 1/2" x 14 1/4" for the 3/4" square channel frame.
The centered miniature logo will probably be 3D printed, not steel.
8" x 14 1/4" ext. dim.s for a mounting frame of 3/4" square channel (steel).
Hive13 logo of steel to weld to center of top of front of frame (3/4" apex to apex hex size for each hex).
Six 3 1/4" apex to apex hexes ( or 2 singles and two stacked doubles) for the active display within the frame. (Probably 3D printed plastic)
Will be adorned in various Hive13 member crafts.
Electronics, sensors, LEDs, controllers, servos, and ideas to display their use.