Difference between revisions of "Kiosk Computer Setup"

From Hive13 Wiki
Jump to navigation Jump to search
m
(Goal of the Project)
Line 9: Line 9:
  
 
== Goal of the Project ==
 
== Goal of the Project ==
The goal of this project is to restore the machine to fully operational condition and install it in the space as an internet connected terminal with information about the space.
+
The goal of this project is to restore the machine to fully operational condition and install it in the space.  I want to create a custom front end UI for it as well that makes it really easy to do space related activities such as:
 +
* Create a end terminal for accessing the internet from the space.
 +
* Tie into the Vending machine so that people could buy an item offline, then trigger its delivery in the vending machine.
 +
* Have access to the space inventory website (When it gets set up)
 +
* Have an easy list of the groups members and contact information.
  
 
== What needs to be done ==
 
== What needs to be done ==

Revision as of 11:25, 2 September 2009

KioskFrontView.JPG

Overview

Kris donated an old computer Kiosk machine that has a touch screen in it. Currently the CPU fan is dead and its working condition is not entirely known.

People involved with this project

  • Paul
  • Kris
  • Add your name here

Goal of the Project

The goal of this project is to restore the machine to fully operational condition and install it in the space. I want to create a custom front end UI for it as well that makes it really easy to do space related activities such as:

  • Create a end terminal for accessing the internet from the space.
  • Tie into the Vending machine so that people could buy an item offline, then trigger its delivery in the vending machine.
  • Have access to the space inventory website (When it gets set up)
  • Have an easy list of the groups members and contact information.

What needs to be done

  • The CPU fan is currently dead.
    • PlayerTwo has a replacement 40mm fan, however the fan is much thicker than the old fan to the point that it touches the outer part of the case. A hole will need to be cut to allow it to pull in outside air, or we need to find a thinner fan.
    • A method for attaching the new CPU fan to the CPU heatsink needs to be devised.
  • Clean OS needs to be installed on it.
  • Drivers found for the touchscreen.

Currently on the ToDo List

  • I bought a 40 mm x 40 mm x 10 mm fan as an alternative to the hole saw with the larger fan. I need to figure out how to mount it on the heat sink.
  • The screen needs to be cleaned really bad.
  • I need to determine how to plug the bare fan leads into the socket for the fan on the board since the plug seems to be missing.

Gallery

Work Log

This is a living log of work that has been completed on the machine.

July 31, 2009 - Bought a hole saw

Because I like purchasing new toys, I bought a 1-5/8 inch hole saw at Home Depot. This should be the right size to cut an air vent over where the CPU fan is going to be.

The hole saw requires a mandrill bit for it to work, I believe I have the correct sized one at my house, but will need to double check to be sure.

I still need to find some kind of material to put over the hole after it is cut, I am thinking that maybe some screen window material will work. Which then leads to the question of how am I going to secure the screen window material material to the inside of the case door?

- Updated added by Paul

August 1, 2009 - A new fan

KioskCPU.JPG

I stopped at Radio Shack today to pick up a composite L/R audio to headphone jack adapter for the space when I noticed they had a 40x40x10 mm fan for $6, I figure that it will probably be a lot easier to use the thinner fan in the case rather than using the thicker fan that would require us to cut through the outer part of the case.

In the picture for this entry, if you open the full size view you can see the socket that the CPU fan plug is supposed to go into. We need to find something that will fit into that socket.