Powermatic Millrite MVM Milling Machine
|The Metalworking Shop Template Is No Longer Used|
|List of All Documented Equipment
|Hive13 Asset Tag: None|
|Make/Model: Powermatic Millrite MVM (google)|
|Arrival Date: 11/2019|
|Does it work?: Yes|
|Certification Needed?: Yes|
|Contact: CNC Warden|
The "Millrite" is a "knee-and-column" type vertical milling machine. Cincinnati is credited as the home for early versions of this type of machine from the 1880's. The product line was intended as a low-cost competitor to the established Bridgeport and other high-class makers of this type of machine, also known as turret mills. The Millrite was of essentially simple but strong construction and offered - on the basis of one main column. It was offered with multiple alternative head, ram and table assemblies.
This is JimD's personal machine. It is on indefinite consignment to Hive13 for gentle use by considerate members. This particular machine is serial number 711226. It was the 1226th machine made in Cincinnati in 1971. Jim bought it from a small machine ship in the New York state finger lake area in 1980, It has been in JimD's home shop for the past 40 years.
Evolution of the Cincinnati company that made this machine:
- 1915: The United States Machine Tool Co. was founded in Cincinnati, Ohio.
- 1947: United States Machine Tool Co. became the US Machine Tool division of Ransohoff Co.
- 1948: US Machine Tool division of Ransohoff Co. merged with Burke Machine Tool and became US Burke Machine Tool Co.
- In the 70s: US Burke became part of the Powermatic/Houdaille conglomerate
- 1979: following in a KKR leveraged-buyout, the Houdaille company went bankrupt and was lost to history.
The company's history is mentioned in From Industry to Alchemy: Burgmaster, A Machine Tool Company by Max Holland. This book was named by Business Week as one of the ten best business books of 1989. We highly recommend this book to anyone interested in the decline of the American manufacturing industry. The book's focus is Burgmaster Corp., which was also acquired by Houdaille; because of the Houdaille connection there is some information on Powermatic as well.
Evolution of the product line:
- Millrite model MV (1960-’64)
- Millrite model MVI (1965-’67)
- Millrite model MVN (1967-’75)
This millrite is a versatile manual machine. It has hand-feed on the X (table) Y (cross-feed), and Z (knee) axes. The standard model had a table with a working surface 7" x 27" with 16" of longitudinal travel. The feed screws are of generous proportions, a full 7/8" in diameter, of Acme form and run through bronze nuts. The cross feed travel of the table was a useful 8" - whilst the head could also be moved in and out of its swivelling support through a range of 12.5". The combination of these movements means it can bring its cutter as close as 4" to the main column yet reach as far away as 16.5". With the head set to swivel, the cutter was able to sweep along an arc with a maximum radius of 25" (12.5" minimum) and cover, in conjunction with table's longitudinal movement, a length of some 62". With the quill retracted, and the knee lowered, a maximum clearance of 17.75" was available between the spindle nose and table - although 5-inch raiser blocks were available to increase this as required.
Fitted as standard with as simple, V-belt drive head powered by a 1 hp, 1800 rpm motor, six well-spread spindle speeds were available in each direction of 335, 575, 970, 2550, 3075 and - very useful for running smaller cutters - 4535 rpm. However, at least three different motors are known to have been offered: a 0.75 h.p. with speeds from 250 to 3400, a 1 hp 1200 rpm unit that gave 250, 430, 725, 1160, 2300 and 3400 rpm - and another 1 h.p. type of 900 rpm with a range of 185, 320, 540, 860, 1700 and 2500 rpm.
For a miller to standard specification the floor space required was approximately 60" x 50" and the weight around 1100 lbs.
The spindle quill taper is R8.
We do Mill and Lathe certification on an as needed basis. Email the warden to request certification. Only the following people are permitted to certify you on the mill:
Certification Goals – Don’t hurt yourself. Don’t hurt the machine.
- Mill safety and setup
- Tool selection for milling operations
- Holding parts using the machinist vice and parallels
- Change tools and set spindle speeds
- “Zero” the X, Y and Z axis using the DRO
- Perform basic facing cuts on steel
- Mount and secure work using parallels and hold downs
- Demonstrate understanding of Backlash
In preparation for certification please; Read the manufacturers manual and study the excellent materials from Case Western
Take the milling quiz.
https://www.proprofs.com/quiz-school/story.php?title=mill-quiz When you have a score of 100% print out the certificate and contact the CNC warden for your certification check ride.
A defect was identified with the Pinion Assembly (enco part number 6116-6S) via borescope on 2/22/2015. Ian and Ryan identified the busticated part.
The endmills are the cutting tools for the milling machine. Wikipedia has a page for these as well.
Hive owns a variety of high speed steel end mills which were purchased used on eBay. They are under the mill labeled 'Good enough'
If you damage one, report it to broken (at) hive13 dot org
WTB (Want to Buy)
- Toolbox // Tool Chest to hold machining parts
- Rotary Table (8"+), one that can be used vertically & horizontally ($100 - $300+)
- Boring head + Boring bar set
- Boring head ~$75
- Boring bar set ~($20 - $60)
Priority Purchase List
Sites to buy from for cheap
Manuals & Guides
- [https://www.scribd.com/doc/58480438/Millrite-Mvn-Manual Online 54 page Maintenance Instructions and Parts List Manual and download link
- Overview of the Millrite line of machines
- User Group for Burke Mill Owners
- Vintage Machinery Website History of the Burke Machine Tool Company
- "Traming" a mill drill
- Motherload of RF-30 Mill Drill guides
- (PDF Link) Interesting book on how to use a milling machine
- The Machinists Handbook
- A Treatise on Milling and Milling Machines (pub 1919)
- Archive.org search for Milling Machine books