|RFID Access System|
|Start Date: 1/12/2012|
2701 Front Door
- Hodapp (software stuff, electronics stuff)
- Drew Kirkman (infra stuff)
- Chris Davis (hardware stuff)
- Dave Velzy (hardware stuff)
Right now this is running from a Raspberry Pi 3B+ with Alpine Linux and some software written in Go. This code interfaces with RFID readers over the Wiegand protocol, communicates with intweb to request access for some badge, and listens over HTTP for 'manual' door open requests. The Raspberry Pi was meant as the "temporary" fix, but..... we know how temporary fixes go. The only thing that makes this Raspberry-Pi-specific is that the software relies on a Pi-specific GPIO library (including some interrupt-driven code for the Wiegand protocol). Besides that, anywhere that Go code runs, and that has controllable GPIOs, "should" work.
Code is at: https://github.com/Hive13/HiveRFID
The badge reader is a generic RFID reader that uses the Wiegand protocol. Other types should work. (USB ones exist too, but would require some additions in the software.)
The electric door strike is a HES 5000 from Assa Abloy. (Installation instructions: https://content.assaabloyusa.com/doc/AADSS1009179&.pdf)
The relay board to switch power to the door strike is a HiLetgo, but almost any solution that can let a 3.3 V signal switch 12V at max 200-300 mA should suffice for this.
The Raspberry Pi is using the uctronics PoE hat (not the mini one). This board was chosen because it exposes a +12VDC supply that is ideal for both the RFID reader, which can run from 6-14VDC, and the electric door strike, which can use either 12V or 24V (see HES5000 docs for the peak current rating).
Diagram to follow, eventually.
Make the following connections:
|Function||RFID reader wire||Raspberry Pi pin||Level shifter pin|
|Ground||Black (Ethernet: brown pair)||GND||GND (either)|
|Wiegand D0 @ 5V logic||Green (Ethernet: green)||RXI channel 1|
|Wiegand D1 @ 5V logic||White (Ethernet: white/green)||RXI channel 2|
|D0 @ 3.3 V logic||BCM 17||RXO channel 1|
|D1 @ 3.3 V logic||BCM 18||RXO channel 2|
|3.3 V||3.3 V||LV|
|5 V||5 V||HV|
|Beeper (active-low input)||Purple (Ethernet: white/orange)||BCM 26|
|LED (active-low input)||Grey (Ethernet: orange)||BCM 16|
- Raspberry Pi BCM 24 to relay board input (on the board we use, "IN").
- GND and 5V to relay board's negative and positive, respectively (on the board we use, "DC-" and "DC+").
- Connect +6-14V power to RFID reader's red wire (the blue pair on the Ethernet cable). The +12V terminal of the uctronics PoE hat works fine for this.
Double-check that D0 and D1 from the reader are always on the high-voltage side (HV) of the level shifter, and that the Raspberry Pi's GPIOs are always on the low-voltage side (LV). If you have no level shifter, this also works:
- Wiegand D0 (green) to BCM 17 through a resistive divider to ground (two 1K resistors)
- Wiegand D1 (white) to BCM 18 through a resistive divider to ground (likewise two 1K resistors)
The resistive divider is because D0 and D1 use 5V, while the Raspberry Pi runs at 3.3V - so they may damage the Pi if used directly. The divider steps this down to a safer 2.5V. Any kind of level shifter that works similarly should be fine here. The beeper and LED pins do not need their level shifted; they are active-low inputs.
HES5000 at Front Door
The HES5000 electric strike had its wires connected to the Ethernet cable run through the front door frame as follows:
|Function (if +12VDC)||Function (if +24VDC)||HES5000 wire color||Ethernet pair|
|Supply +||Supply +||Red||Orange|
|Supply +||Connect to blue||Purple||Brown|
|Supply -||Connect to brown||Black||Blue|
|Supply -||Supply -||Red/green stripe||Green|
The left two columns simply repeat what is in the HES5000 installation manual.
(This was tested to work in the +12VDC mode with the +12V supply from the uctronics PoE hat, and in the +24VDC mode with a ~20V laptop supply.)
Using the strike's +12VDC mode with the uctronics PoE hat and the current relay board, connect:
- +12V terminal from PoE hat to the relay board's "COM" pin
- GND terminal from PoE hat to the badge reader's negative supply (i.e. blue and green pairs)
- Relay board's "NO" (normally open) pin to the badge reader's positive supply (i.e. brown and orange pairs)
Note the other connections to the relay board in the above section.
RFID Reader at Front Door
Likewise, the RFID reader's wires were connected to Ethernet cable, and uses the same mapping as the old space:
|Function||Scanner wire color||Ethernet wire color|
Note the connections in the "Wiring" section, and the warnings about the D0/D1 pins. They are 5V logic, so a level shifter is needed to connect them with 3.3 V logic.
This will be turned to a better diagram at some point, but the tentative wiring used for the Pi on the DIN rail is given below:
A photo of the inside (as of 2020 August) is here:
- More complete documentation on wiring
To do (software)
- Restricted WiFi backdoor in case intweb goes offline
- Back up this Linux image someplace that people can find it easily if needed
- Migrate away from WiringPi, which is unsupported
- Make better use of beeper and LED?
To do (longer term)
- Once the updated intweb/HiveWeb is in place, migrate the code to use this REST API instead.
- Make a newer version with cleaned-up wiring. Perhaps use a balenaFin with PoE and the DIN rail case
- Make a version that can run on microcontrollers like the ESP8266 or ESP32 rather than a Raspberry Pi. (Dave B. is interested in the electronics for this, possibly in integrating nearly everything into a single board.)
Overview (archived for 2929)
This older section was left in place for the moment. It refers to some work done originally at 2929, some of which was still in use at 2701, but almost all of which is in the process of being updated.
The purpose of this project is to build a modular RFID Access System for all of the tools, doors, and vending machines in the Hive.
- Uses the Access Protocol
- Accepts NFC tags and phones with NFC for access and tracking control (our badges run at 125 KHz)
- Central database (Postgres, accessed via HTTP, served by a Perl Catalyst app)
What needs to be done
Main Door RFID
Battery backup somehow?It's PoE and that's on battery backup.
- Have it log temperatures
Annex Door RFID
- Schematic and PCB is on GitHub
- Battery backup somehow?
- Motion sensor so it unlocks when you approach it from the inside.
- Consider switching it to wired for power backup reasons.
- Add in a mechanical key for when the power's out.
Vending Machine RFID
- Get compressor being controlled by the Arduino
- Mount the relay board instead of it being set on a block of wood
- Clean up the wiring
The Snack Vending Machine has been gutted, its coin validator removed, and RFID card mounted to the machine, however, no work has been done to bring that machine to vending status.
Places it'd be nice to have badge readers
- Doors out to annex hallway
- Outside door by the Dumpster
- Certification-only tools
One of the goals of this project is to build a case where cash payments to the hive can be recorded (and membership automatically extended), and cash payments can be automatically made to the card for the purposes of purchasing sodas.
This project is in the planning phase right now -- however, if you want to help, I would appreciate the time and can provide my guidance for this project.
- The annex uses a WeMos D1 mini.
- The main door uses an Arduino Mega.
Scanner to MCU wiring
- This is correct for the annex door
- The main door needs to have its wiring changed to match.
|Function||Scanner Wire Color||Ethernet cable wire color|