Vinyl Express Vinyl Cutter
|3D Printing||2D Cutting||Misc|
|List of All Documented Equipment|
|Hive13 Asset Tag: None|
|Make/Model: Vinyl Express Q60 (google)|
|Arrival Date: 1/15/2015|
|Does it work?: Yes|
|Certification Needed?: No|
|Contact: Fab Lab area Warden|
Fully functional. Donated by a friend of Dave B (Tony). Will cut up to 24" vinyl sheets.
The hive should figure out a system for stocking vinyl and charging for it (just to break even).
Install driver. Plug in Vinyl Express Q60 into your computer. Under device and printers you should see an unspecified ‘USB Printing Support’. Right click and select ‘Troubleshoot’. It should automatically install the drivers, and then identify the Vinyl Express Q60 under Printers and Faxes.
Network Access (July 2019)
The vinyl cutter is available over IPP at http://slice.at.hive13.org:631/printers/VinylExpress_Q60 Linux and Mac devices should handle this fairly well (install the generic text-only driver). Windows 10 needs IPP support enabled, you can do this with PowerShell...
Enable-WindowsOptionalFeature -Online -FeatureName Printing-Foundation-InternetPrinting-Client
Let it chug for a bit, then you're ready to download the printer driver from the links at the bottom of this page. Once you have the zip file extracted, you are ready to go to the "add a printer" sequence in Windows. Tell windows it sucks at searching for your printer ("The printer I want isn't listed") and type the URL in the box that appears, as shown to the left.
At this point you'll be asked for the printer drivers. Click the "have disk" button and browse to your extracted driver folder. The Q60 is a rebranded Graphtec FC-7000, so select that one from the list.
Now you're ready to shred some vinyl and if you're really lucky, you'll have a good looking cut to stick on your laptop. Or something.
To Do (2019 Redux)
- Fully document InkCut setup and scaling settings.
- Fully document SCALP 5 setup and scaling settings.
- Review the manual for the Graphtec FC-7000 Mk2.
- Adjust the cutting area on the cutter controller so the margins aren't so goddamn huge.
- Clean up this Wiki page.
- Back up CUPS config from Raspberry Pi.
If you're on Linux, add the IPP queue and install InkCut from Code LV. https://www.codelv.com/projects/inkcut/ You can import SVG files to this program and cut them.
A vote is forthcoming to purchase Sure Cuts A Lot Pro (SCALP) v5 for the CAD workstation. I have tested it with the cutter and it works.
I use Inkscape 0.48.5 to prep my image, but you need a program to actually cut the Vinyl. I used Sign Cut, but Linux has a free app linked to Inkscape called Inkcut. Some people have had success in running Inkcut on windows, and there is a tutorial here.
To print an image using Inkscape and Signcut, choose any image, and open it inside Inkscape. With the image selected, go to ‘Path > Trace Bitmap...’. Edge detection seems to be the easiest to use, but play around with settings. The lower the threshold the more detailed the picture. Keep it around .5, but may vary depending on what image you are using. When you are done with that, select your bitmap image and go to ‘Object > Fill and Stroke...’. In the ‘Fill’ tab, click the ‘X’. This will cause your image to disappear temporarily. Now click the ‘Stroke paint’ tab, and click the blue rectangle (right of the ‘X’). This will render your image so that It can now be cut. Save your image (for Signcut, .svg is fine) and you can now import into your cutting program.
Once you're ready to cut, turn on the vinyl cutter. select 'Rear Set' (Roll-1 or Roll-2 doesn't matter for this cutter). If it's says 'Front Set' press the left or right position button until it displays the 'Rear Set'. Press 'F1'.
The next screen will say 'Press enter key after releasing media lock'. Here is where you can release the media set lever and adjust the pinch rollers. The distance between the pinch rollers determine how wide of a printing surface you have to work with, so adjust to the edges of the vinyl. I try to leave about an inch of wiggle room on each side. Once the media and the pinch rollers are aligned, pull the media bar back into it's default position and press enter.
The pen carriage will now calibrate and sense the cutting distance between the two pinch rollers. Once it's done calibrating, it will say 'Condition #' and display ready. Once you get to the ready screen you can print from your vinyl cutting program.
WARNING!: When on the ready screen, you can adjust the Force, Speed, Quality, etc. A Force of 14 barely didn't cut all the way through, and 35 ripped the vinyl. Force of 20 seems like the best average setting.
Inkcut scaling settings
x = 2.86
y = 2.93
SureCutsALot or Easy Cut Studio resolution settings
x = 0.701 in
y = 0.701 in
HPGL vs. GPGL - Inkcut on Linux
When using Inkcut from Code LV on Linux, I had much more luck switching the cutter and Inkcut to using GPGL instead of HPGL - the software doesn't seem to insert HPGL "pen up" commands and the cutter will happily shred the vinyl. -User:Kungfoo
To switch or verify the command language used on the cutter:
Archived from SignWarehouse.
Install drivers from sign warehouse or graphtec (The sign warehouses Q60 is essentially a re-branded Graphtec FC-7000)
https://www.graphtecamerica.com/s/OPS662ver300-z22p.zip <- CURRENT AS OF 2019 (Windows x64)