Paragon F130 Lampworking Kiln
| Ceramics |
|---|
| Jewelry & Metalsmithing |
|---|
| Hive13 Equipment |
|---|
| List of All Documented Equipment |
|
| Owner/Loaner: Kevin M. |
| Hive13 Asset Tag: HV0360 |
| Make/Model: Paragon F130 Lampworking Kiln (google) |
| Arrival Date: September 2023 |
| Does it work?: yes |
| Certification Needed?: yes |
| Contact: Kevin M |
| Floorplan: Hot Crafts Area |
| Manual: Manual |
|
About this Item
This is a kiln specifically designed for torchwork. It has a chamber size of 11" wide x 11" deep x 12" tall. It has a small flap door for placing glass parts attached to mandrels, blowtubes, and punties through to soak in heat while working, or the entire front opens vertically with a guillotine style door. It has a max temperature of 1700°F, and runs on 120v at 20 amps, for a maximum power of 2400 watts. This kiln belongs to Kevin M. and is on loan to the hive for anyone to use for lampworking projects.
Manuals and Manufacturer's Data
Kiln Manual
Controller Manual
Manufacturer's Website
Starting A Program
- Check if it is on already and if it is in a cycle. If cycling, let it finish. DO NOT OPEN THE ANNEALER IF IT IS CYCLING, ANNEALING GLASS. Opening the annealer at any time it is not holding the loading temperature for loading or cooled to below 200F will cause the glass in it to crack. If off, or cycle is complete and temperature has reached under 200F, empty the annealer of any annealed pieces.
- If off, flip switch up to turn on. wait for the temperature controller to boot up and the display to reach a stable rotation of information. If it says anything other than Idle/<Current Temp>, press the Start/Stop/Enter/Program button till it says Idle/<Current Temp>.
- Press the Start/Stop/Enter/Program button to enter the program list.
- Press Up Arrow/Higher button to scroll through the available programs till the display says the program you want. Only the up arrow may be used to scroll through the list, if you go past the program you need, just keep scrolling up till it comes back around.
- PR01 is programmed for Garaging and Annealing Soft Glass
- PR02 is programmed for Garaging and Annealing Borosilicate Glass
- PR03 is programmed for Lost Wax Burnout
- Once the desired program is located, press the Down Arrow/Lower/Delay/Review button to enter the "Review" mode for that program. The "Review" light will turn on, and the screen will begin cycling through the steps of the program.
- Press the Start/Stop/Enter/Program button to start the program.
- The display should show “-ON-” and the run light should start blinking (if not, Press the Start/Stop/Enter/Program button again). In a few moments the red light below the controller should turn on indicating the annealer is heating.
- While running, the display will indicate the current temperature of the annealer. Do not load any glass in the annealer until it reaches at least 925F. Loading glass in the annealer at less than 925F can cause it to crack.
Starting Annealing For Glass Programs
When you are done making and loading glass pieces, and ready for the annealing to begin, you must skip the infinite hold that is programmed in for garaging/loading.
- Press the Up Arrow/Higher button till the "SStp" (Skip Step) option appears on the screen.
- Press the Start/Stop/Enter button to select the "SStp" (Skip Step) option.
- The screen will display "Hld1", press the Start/Stop/Enter button to confirm you want to skip step Hold 1
- The screen should now no longer be flashing between a temperature and "99:59" as it was during the infinite hold garaging step, instead it will display the temperature and begin to ramp up the temperature to the annealing temperature. Once the annealing temperature is reached, it will begin to flash between the current temp and the remaining hold time (starts at 1 hours and counts down).
- The full annealing cycle takes between 2 and 3 hours to run, and then an additional 2-3 hours for the kiln to cool to unloading temperature (below 200f). Do not open the kiln till it reaches unloading temperature (below 200f).
Programs
PR01 - Soft Glass up to 1" thick
| Step | Ramp (°F/Hr) | Temp (°F) | Time (HH:MM) |
| 1 | FULL | 950 | 99:59 |
| 2 | 400 | 970 | 1:00 |
| 3 | 374 | 860 | 0:20 |
| 4 | 364 | 700 | 0:00 |
| 5 | 0 | 0 | 0:00 |
PR02 - Boro Glass up to 1" Thick
| Step | Ramp (°F/Hr) | Temp (°F) | Time (HH:MM) |
| 1 | FULL | 1030 | 99:59 |
| 2 | 400 | 1060 | 0:20 |
| 3 | 374 | 950 | 0:20 |
| 4 | 364 | 700 | 0:00 |
| 5 | 0 | 0 | 0:00 |
PR03 - Unused
This is a user-defined program that has not yet been set for a specific purpose.
PR04 - Unused
This is a user-defined program that has not yet been set for a specific purpose.
SPD1
200°F/Hr ramp to specified temperature and held for a specified time.
SPD2
500°F/Hr ramp to specified temperature and held for a specified time.
SPD3
1000°F/Hr ramp to specified temperature and held for a specified time.
SPD4
1500°F/Hr ramp to specified temperature and held for a specified time.
SPD5
Full power ramp to specified temperature and held for a specified time. SPD5 is useful for enameling: run with temp set to 1450°F, hold set to 99:59 (forever).
Programing References
https://www.youtube.com/watch?v=MwA82ZO0lKM&feature=emb_title